清晰度-嵌入式板
2022世界杯热身赛赛程应用机械技术在工业废水处理组件和系统方面居领先地位。自1997年以来,我们为各种行业设计并搭建工业设备和系统
设计并搭建核心技术设备全线设备包括:
- 油水分离器
- DAF解析空气浮点
- 嵌入式板解析器
- 多媒体滤波
- 控件包
以上是系统全包核心部分。我们用战略OEM关系完成系统,包括工具、泵、阀门等所有其它必要组件
设计制造核心设备和系统时,我们拥有灵活性和能力按需配置系统,满足最严格项目规范,同时超出客户期望
操作原理解析器
Clarifiers are devices that exploit the laws of physics in that they permit solids to exit via settling in a wastewater stream while the stream is flowing and has velocity. In the simplest terms, we do this by designing a system where the settling rate exceeds the velocity of the flow. This actually works in mirror image to how an Oil Water Separator works (Click to see Oil Water Separator principal of operation). In an Oil Water Separator we calculate the rate of rise, in a clarifier we are concerned with the rate of settling or sedimentation. In both cases we are concerned with the rate being such that the particle (oil or solids) will settle or rise at a rate sufficient to prevent exit before it reaches the effluent section.
In a clarifier we use plates tilted at an 55d steep angle and spaced 2" apart typically. This is done for the same reasons an Oil Water Separator has coalescing media, to increase surface area in a smaller package. As the wastewater flows into the bottom of the plate in an upward flow path to exit the clarifier, the settling solids will land on the plate where they impinge. The solids will gather, increase mass and begin to slide in a down path on the plate toward the sludge chamber. All the while the wastewater flow is in an upward path. This is referred to as laminar flow as there are more than one layer or laminate. It is essential in clarifier design that the settling rate of the particle is greater than the upward velocity in the plate pack or the particle will be carried out.
This is where it gets tricky. Sizing a clarifier is done on a Hydraulic Loading Ratio or HLR that is defined as ratio of GPM/FT2 of projected surface area. Projected surface area is the total area of the tilted plate as projected upward to a flat plane. In other words, a 2x4=8 ft2 plate lying flat projects 8ft2. If the plate is then tilted upward at 55d, the resulting projected surface area less. It is calculated by multiplying the area by the cosine of the angle. The formula is cos of 55d=0.57. Therefore a 2x4=8ft2 plate X 0.57=4.56 ft2 of Projected Surface Area or PSA.4.56x牌照数定义HLR中的FT2
典型晶体化使用HLR0.1-0.5gpm/ft2和0.25gpm/ft2为多项应用基准。粒子沉积速度越慢,HLR速度越低,粒子沉积速度越快HLR速度越高
Settling rate is not the only important consideration. Plate pack velocity is actually equally important of a consideration. If you make a plate pack of 8' tall plates, at 2" spacing and a clarifier of 250ft2 PSA it will have twice the velocity of a plate pack that is 4' tall, all other things being equal. We make clarifiers with 4' tall plates, 6' tall plates, 7' and 8' tall plates. The 6' tall plate strikes the best balance when it comes to overall design, performance, and cost which is why our 6' tall plate ClariMore clarifier is the most popular, most cost effective and best performing clarifier configuration. Having a manageable height it tends to fit into rooms better than taller clarifiers, also making it popular.
清晰底部配置清晰度底部以多种形状和样式生成 。 有条纹样式加粗体、金字塔样式加旋转矩形并循环样式除圆形样式外全部生成 。这主要归因于成本效益 。 环形样式比外部污泥槽成本很容易决策 。外部污泥池胜出Our ClariMore clarifier with trough bottom and rotating auger is the best in the business as it is the only one with a half pipe clarifier bottom with a radius that conforms to the auger shape with less than 1/2" gap. Our ClariClear, the economy clarifier for < 100 gpm applications has a half round sludge hopper bottom. Good performance and low cost design. Other brands have a V bottom or a truncated V bottom with a round auger, neither bottoms match the shape of the radius shape of the auger. Truly a square hole with a round peg… Our IPC Clarifier has a pyramidal bottom and is very cost effective as a result however the geometry of the bottom makes for a taller clarifier as a result. If the sludge generated tends to compact then the pyramidal bottom could be problematic.
清晰排出系统并用几种样式出现 。 我们所有晶体都拥有不锈钢可调整锯齿网路 。 污水网路调整对补偿不均匀楼层很重要,最重要的是实现完全偶流速率和速率所有板块 。 偶流率保证稳定沉积性能并减少电磁短路
清晰底层Augers-Rakesif so equipped come in a couple different styles. The auger is a horizontal ribbon screw type auger with converging flights so that one direction rotation appears that the ribbons are converging from outside to the middle. The middle is therefore where the sludge outlet nozzle is positioned. The style, size, pitch and rotation speed are all very important. The wrong auger can cause problems like rat holing, current eddies and can stir the sludge up and liquefy it rather than gently move and thicken it as properly designed auger can do. Our augers are designed based on many years of experience in a variety of different applications. These are the same augers that can be found in our Clarifiers and Oil Water Separator designs.
闪电Floc混合系统系统先于解析器和DAF系统。这些系统是化学增强系统,使良好的处理结果成为可能。没有这些系统,我们无法破解仿化机、沉积金属或聚积固态物。它们是分解器前的工作马(DAF和Clarations技术分解器)。如果离析器或化学分解器失灵,DAF或Claration-句段也不会正常工作。点击这里.
我们为各种行业编译解析符,包括但不限于:
- 金属电镀转换涂层
- 地下水修复
- 固态清除
- 易发性减低
- 化学Etch浴水
- 底层飞灰槽水
- 冲洗水
- 冷却塔水
典型选项包含:
- 软钢或不锈钢构造
- 高腐蚀性应用特殊涂层
- XP爆炸验证电气组件
- 底部淤泥调试器
- 完全控制包
- 泵滑动,插件,污水,污泥
- 化学服药和High-Floc混合系统
- 反射破解系统
- 运算符平台
- 流水过滤器
质量学
我们只使用最高质量材料、泵、工具、阀门和控制组件以确保你在当前高度竞争市场环境中需要的重税强性能所有系统都建到最高标准手艺并在整个编程中广泛测试我们执行各种NDE测试,包括PQR、UT、XT、全水电、染色穿孔测试、ASME压力测试和自然视觉检验和实战功能测试
控件
操作者控件界面机制最先进废水产业。我们向使用SQL数据库平台全功能控件系统提供基本简化控件,允许生成、归档和管理所有向导和流出数据。我们最高级控件提供操作者输入轮廓可处理性测试并允许系统使用内部设计并搭建所有控件UL-508A工控板标准,严格符合NECANSI/NFPA70规则
坦克洗刷系统
工业洗坦克司设计并搭建铁路和坦克拖车内部冲刷系统清洗从粗油到易腐油、从化学品厂到康星和中间的一切。当你洗工业槽时,你制造工业废水,我们也处理这些废水。
Viewpdfs获取更多信息